Leaking, Corroded, or Burst Pipes in Lometa, TX? Masters Plumbing Service Fixes It
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Lometa, TX use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
How Masters Plumbing Service Approaches Pipe Repair in Lometa
Our techs work on every pipe material found in Lometa, TX homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Press-fit copper connections — particularly useful for repairs in occupied spaces where open flame is a concern — are available as an alternative to torch sweating where code permits.
🔒
Pressure-Tested Before We Leave
Every supply line repair is pressure-tested before we close the wall or floor. We pressurize the repaired section, hold the test pressure for the required duration, and confirm zero drop before considering the repair complete. You don't find out there's a second leak next week — we find it before we pack up.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
From a pinhole copper leak behind a kitchen cabinet to a full galvanized repiping, our pipe crew in Lometa, TX handles the full range.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
Galvanized steel pipe was standard in homes built before the 1960s. It corrodes from the inside out — zinc coating depletes, iron oxide (rust) accumulates on the inner wall, progressively narrowing flow and leaching into the water supply. Repairs on severely corroded galvanized are generally temporary; the pipe is failing systemically along its full run.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
A burst pipe from freezing or sudden pressure surge requires immediate water shutoff and precise repair. We locate the failure, determine whether it's a single failure point or multiple freeze-damaged sections, and repair with a method appropriate to the pipe material — press-fit coupling for copper, expansion coupling for PEX-A, or a mechanical repair coupling for emergency situations.
Slab Leaks
Under-Slab Pipe Leak Repair
Slab leak rerouting is often more cost-effective than direct access, particularly for longer runs or under tiled floors. We present the options honestly with pricing so you can choose based on your priorities.
Full Repipe
Whole-House Repipe Service
A full repipe in Lometa typically completes in 2–3 days for a standard single-family home. You're without water for a portion of each day; we plan the schedule to minimize disruption to occupied rooms.
We don't open walls at random. Acoustic and thermal detection tools tell us exactly where to cut before we pick up a saw.
1
Call & Describe — We Shut the Water If Needed
For emergency burst pipe calls, we dispatch immediately. For suspected slow leaks, we schedule at the earliest available slot and confirm before arrival.
2
Pressure Test & Acoustic / Thermal Detection
This detection step routinely saves homeowners $500–$2,000 in unnecessary drywall removal compared to opening walls speculatively.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
Repair executes immediately on approval. After the repair, we repressurize and hold a pressure test to confirm the failure is fully resolved — not partially. The access opening is left clean for your drywall patch or left ready for your contractor.
Customer Reviews
What Lometa Customers Say About Our Pipe Work
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Lometa
★★★★★
Our galvanized supply lines finally gave out — low pressure everywhere, rust-colored water at some fixtures. Masters Plumbing Service repiped the whole house with PEX over two days. They confirmed pressure and flow at every fixture before leaving, patched all the wall access points smooth, and cleaned up each work area. One year later, no issues at all.
— O. & R. Adeyemi, Lometa, TX
★★★★★
Pipe burst in a rental property at 2 AM — Masters Plumbing Service's emergency line answered immediately, talked my tenant through the main shutoff, and had a tech there in 45 minutes. Freeze crack in a PEX line in an exterior wall. Repair and insulation wrap done in under two hours. Detailed receipt for insurance documentation. Exactly what I needed as a landlord dealing with a crisis remotely.
— F. Okoro, Lometa, TX
Common Questions
Pipe Repair FAQ for Lometa, TX Homeowners
Watch your water meter with all fixtures off. If the meter dial is moving or the leak indicator light is turning, water is escaping somewhere in your supply system. Other signs: unexplained increases in your monthly water bill, soft or discolored spots on walls or ceilings, mold or mildew smell in a room without a visible source, or a running sound inside walls when all fixtures are off.
In most cases, the pipe itself needs to be physically accessed to make a durable repair — but the amount of wall we open depends entirely on how precisely we can locate the failure first. With acoustic detection and thermal imaging, we typically open a single, small access point rather than a wide section of wall.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
Galvanized pipe corrodes from the interior outward — by the time one section fails, the rest of the pipe is in varying stages of the same process. A localized repair buys time, but another section typically fails within 1–3 years if the system is at end of life. The honest answer is: it depends on how far along the corrosion is and how many sections are already narrowed or showing surface rust.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
For slab access openings, we clean up concrete debris, complete the pipe repair, and patch the concrete. Tile or flooring restoration over a slab patch is normally a separate trade.
Service Area
Your Local Pipe Repair Specialists in Lometa, TX
Our techs are stocked with the copper, PEX, and CPVC materials most commonly needed in Lometa homes and businesses.
